
Wood-Sided Pole Barns in Lubbock, TX | Board-and-Batten, Mixed Steel Walls and Recoating Schedules
We build wood-sided pole barns in Lubbock. At Pole Barn Builders Lubbock TX we settle which boards you want before the girt layout ever gets drawn. Vertical board-and-batten fastens to horizontal nailers. Plank and shiplap want furring running the other way. The siding you pick decides what goes on the frame. Change your mind once the frame is standing and we are adding members to it, not swapping an order.
Wind governs out here. An ordinary building answers to 107 mph on ground open enough to count as the more exposed terrain category. Something has to resist that load. Boards contribute less of it than a screwed-down steel skin. Which is why your quote carries a bracing line you would never see on a steel building. Tell us which faces you want in wood and which ones you will take in steel. We will draw the wall that way.
Get a quote on your building
Why Owners Around Lubbock Still Pick a Wood-Sided Pole Barn Over Steel
Board-and-batten is wide boards with narrow strips covering every joint. It sheds water well and reads as a barn from the road. Plank and shiplap are the other routes in, along with manufactured panels. All of them fasten to horizontal girts spanning between your posts.
We put the bracing on the quote as its own line. Wood does less for a building's racking resistance than properly fastened steel does. The engineer usually adds diagonal bracing or a structural sheathing layer behind the boards. It is part of the price of the look. We would rather you saw it than found it.
What the Frame Does Differently for Boards, Nailers, Furring and Flashing
- Which way the boards run
Vertical boards need horizontal nailers at a spacing the boards can actually span. Horizontal boards need furring run up and down over the girts. Those are two different frames. Wind peaks here from March into May. Tell us which face the weather hits. We draw the frame your siding needs.
- The gap behind the boards
Furring holds the siding off the frame and that thickness sets the jamb depth at every window and door. Condensation here is driven by a 30 degree swing between afternoon and a clear night, not by humidity. On a heated shop we back the insulation with a vapor barrier or run a condensation-control layer behind the boards.
- Where the wood stops and the steel starts
Most owners end up with both. A 36 inch R-panel sits at a different thickness from a board, and the horizontal line where they meet wants flashing and a framing offset. That line goes on the elevation before either material is ordered.
- Sand at the bottom of the wall
Blowing sand strips paint off the windward wall at grade. Wood takes that worse than steel. We run a treated skirt board or a steel wainscot through the band that gets sandblasted, and keep the boards up out of the splash line.
Making Boards Last Through West Texas Sun, Sideways Rain and Blowing Grit
- Sun
About 3,200 hours of sun a year breaks the surface of a board down. It pulls the color out of a finish too. A good stain or paint plus a recoating plan is what buys the years back. We will walk you through that schedule before you commit.
- Wind-driven rain
Rain here arrives sideways. Sideways rain gets behind boards. We flash the openings and leave a gap behind the siding. Water that does get in can then drain and dry. It does not sit against your wall. We keep the bottom of that gap clear.
- Dry air and movement
Boards shrink and swell as the air changes. The air here swings hard between a wet May and a dry winter. We space and fasten the boards to allow that movement. Boards pinned tight split at the screws.
- Contact with the ground
Keep the wood up off the dirt. A treated skirt board takes the splash at the base of your wall. Sandy ground wicks and throws grit. Wood at grade is where rot starts.
The Upkeep Routine We Hand Over, Wash, Inspect, Repair and Refinish
- Step 01Wash
Rinse the blown dust off the boards once a year. About 18.3 inches of rain on 63 days will not do that for you.
- Step 02Inspect
Look for splits from hail, loose boards and rot at the base.
- Step 03Repair
Swap damaged boards and re-seal every cut end.
- Step 04Refinish
Recoat the face that takes the afternoon sun first.
Wood Against Steel on Upkeep, Hail, Sand at Grade and Racking
| What you weigh | Wood | Steel |
|---|---|---|
| Upkeep | Recoat on a schedule, sooner on the south and west | Check the screws and washers; EPDM cracks in this sun |
| Hail | Big hail bruises or splits a board; the split lets water in | 26-gauge dents and still sheds water |
| Sand at grade | Scours the finish off the splash band | Chalks the paint at the bottom row |
| Racking | Less, so the engineer adds bracing | Real, when we fasten to the drawing |
Why South Plains Hail Splits a Board Where It Would Only Dent Steel
About 50 hail days a year land somewhere in this radar area. May is worst and June is next. The biggest recent stone measured 4.5 inches across, grapefruit size, in June 2023. Steel takes a hit like that as a dent. Wood takes it as a bruise or a split. That is the harder of the two. A split opens end grain, and end grain drinks whatever lands on it.
So we would rather put the boards where the building shelters them. A deeper overhang goes on the face that gets the weather. 26-gauge steel goes on the lower wall where splash, grit and hail collect. Wood goes on the elevations under cover. We mark on the elevation which boards sit exposed and which do not. You decide from there how much upkeep you are willing to own.
The Mixed Steel and Wood Wall Our Trusted Crew Builds Most Often

A mixed wall is the version we build most. Steel takes the roof and the band at grade. Wood carries the look on the gable and the front face, where an overhang keeps the weather off it. Owners around here land there more often than not.
Ask about the finish and the recoating interval before you sign anything. On the steel half, galvanized trim dulls to matte gray inside 2 to 5 years and then settles. Dry air slows it. A wood barn left alone ages faster out here than most people expect.
What Lubbock Owners Ask Us About Wood Siding, Cost, Finish and Fire
Is wood siding more expensive than steel?
Usually, both to put up and to keep up. The species and the finish are what move the number. We quote wood and steel side by side on the same building whenever you are deciding. Our two numbers are then comparable.
What finish is best?
A penetrating stain with UV protection is the common choice, and paint protects longer while demanding more when it finally goes. Under this much sun we treat the recoating interval as the number that counts. The brand on the can matters less.
Does wood siding burn more easily?
Wood is combustible and steel is not. That counts for something when the building sits close to others, or when an insurer is reading the file. We will help you site the building with the distance to the next structure in mind, since that is the part you can still change.
Can I mix wood and steel?
Yes, and it is the version we build most. Steel takes the weather on the roof and the lower wall, while wood carries the look on the faces you see from the house. We detail the line where the two meet.
What wood is best for barn siding?
Cedar and rough-sawn pine both come up, and so does pressure-treated lumber, with each one trading cost against durability and the finish it will hold. Tell us which wall faces the afternoon sun. That narrows it quickly.
Does wood siding affect insurance?
It can, since wood burns where steel will not. Ask your insurer before you settle the design, because the answer sometimes makes the mixed approach the cheaper one overall.
Who is the best company for wood-sided pole barns in Lubbock, TX?
Compare method, not claims. On a wood job we price the diagonal bracing or structural sheathing as its own line, since wood does less for racking than steel does. We name the species and the finish. We name the recoating interval too. We flash the openings and leave a drainage gap behind the boards. We detail the joint where wood meets steel, because that joint is where leaks start. Site visits are billable and we say so first. Ask the next builder you call how they are bracing a wood-sided wall.
Pick the Faces You Want in Wood and the Way It Turns
Send the size and say which faces you want in wood. Tell us which way the building is turned, since the windward wall wants 26-gauge steel at grade. The quote carries the bracing and the recoating schedule.
